Trendnet TEG-S4000I Bedienungsanleitung

TEG-S4000i 4-Slot SNMP Modular Switch Ethernet / Fast Ethernet / Gigabit Ethernet User’s Guide Version 2.0 23-April-2003

The 3-pronged power plug and On/off switched are located at the Rear Panel of the Modular Switch displayed in Figure 2-2. The Switch will work with AC

RS-232 Console This Console port is used to connect a management station or terminal with the switch. Out-of-band management means go through the RS

Virtual LANs ( VLANs ) A VLAN is a group of switch ports designated by the switch as belonging to the same broadcast domain. This feature allows wo

Port Mirror Port mirror allows user to define a destination port and a target port , all the packet on the target port will be copy and resend to dest

3. Network Configuration This chapter provides 3 network configuration examples by using the Modular Switch:  Collapsed Backbone Application  Dep

When the network needs expansion, you can simply daisy-chain the switch to any IEEE 802.3 ( Ethernet ), IEEE 802.3u ( Fast Ethernet ), IEEE 802.3z ( G

Figure 3-2. Departmental Bridge Application NOTE: Full-duplex operation only applies to point-to-point access (for example, when attaching the switc

IEEE 802.1Q VLAN Application The switch support up to 4095 port-based 802.1Q-compatible virtual LANs (VLANs). Port-based VLAN Workg

Shared Server The switch compliant to the IEEE802.1Q tagging VLAN standard allows ports to exist in multiple VLANs for shared resources, such as se

4. Connecting to the Network This chapter provides the installation procedure and instructions for assigning IP address. This chapter contains f

Release Note 4 slot modular switch manual Update Version Progress status Remark QA PM 23/04/2003 V2.0 On checking 1. 10/100 TX (48350) spec.

Mounting the Switch The Modular Switch is suitable for use in an office environment where it can be rack-mounted in standa

Rack Mounting The Modular Switch come with a rack-mounted kid and can be mounted in an EIA standard size, 19-inch Rack. The Switch can be placed in a

Figure 4-3. Figure 2-5. Mount the Modular Switch in an EIA standard 19-inch Rack Note: For proper ventilation, allow at least 4 inches (10 cm) of

Diagnostic Test After the installation is completed and AC power is applied to the switch, the system will automatically perform a diagnostic test.

After connected to the Console port, turn on the PC or terminal and configure its communications parameters to match the following default characteri

Assigning IP Address After you have attached a terminal or PC with emulation software and you are ready to make a connection

Select IP Address on the Device page, and enter a unique IP address for the switch, and press Enter. ( Default IP address is 192.168.16.1 ) Select Su

a. More function to choice after typing 1, or 2 b. Pick any number you need to set up, for example, the option 2 is for the Full or Half mood sett

Address table User can view the node’s MAC address table of system, per module or per port, that attached on the devic

Broadcast Storm Filter IGMP Internet Group Multicasting Protocol (IGMP) is use

Table of Content Introduction Product Overview Network Configuration Connecting to the Network Web-Based Management SNMP Management Product Specifi

VLAN Mode (2 modes) VLAN For Cpu(2 VLANs) 30

Secure IP for Telnet and HTTP The IP security is for Telnet and HTTP , if device is installed in a internet environment , swi

5. Web-Based Management This section introduces the configuration and functions of the Web-Based management. About Web-based Management Insid

Figure 5-1: The Password Window 3. The Password screen appears. 4. Type user name and password. The default is “ root ” for both. 5. Press “Ent

Home The Home page displays the configuration of the Modular Switch. System Name : An administratively-assigned name of the managed unit, can be modi

Modules Modules page shows the modules that have installed into the Modular Switch. In the following example, 1-port Gigabit 1000Base-T Switch Module

Ports Inside Ports page, you can enable/disable each port, configure Speed/Duplex for each port, and assign VLAN ID. The Port Management table shows

window. Statistics The Statistic page displays the detailed information about each port. You can compare and evaluate throughput or other port para

• Collision: the total number of collisions that occurred during reception and transmission You can clear 8 counters of some ports by select the cor

VLAN ( Virtual LAN ) A port-based VLAN is a group of switch ports designated by the switch as belonging to the same broadcast domain. If a broadcast

1. Introduction Welcome to the World of Switching-Network. In modern business society, communication and information sharing are fundamental to our

Figure 5-6 The VLAN Page In the VLAN management window, you will see 2 VLANs in the page. To select a certain VLAN, you can do the following: • Pre

Figure 5-7 The Trunk page You can add, edit and remove port members of each trunk and then press "Apply" button after you have finished con

Figure 5-8-1 The STP upper page If you want to participate in spanning tree, have the "Enable Spanning Tree Protocol" checkbox selected.

Max Age: the amount of time (in seconds) protocol information received on a port is stored by the root switch, the default value is 20 Hello Time: h

Figure 5-8-1 The STP lower page Note: when you enable the spanning tree protocol, because all ports in the switch will listen and learn, you may lose

Port Security Port Security allow you to restrict specific MAC addresses to reside in some port. For example, a dummy hub is attached to some port for

option. Priority There are two priority queues ( high and low ) on each port. Each port arbitrates between two transmit queues ( high and low prior

Priority 2 Each port can parse the header of an incoming IPv4 header and identify the Type-Of-Service byte (TOS field). This is extremely important

Figure 5-11. Port Priority – Type of Service IGMP (IP Multicast) IGMP is used in multicast communication network applications where one or more s

Static Address You can lock a certain MAC address ( associated with a host, ) to a certain port. Once a certain MAC address is locked to a certain

1000Base-SX/LX Intelligent Fiber Modules. With its build-in Web-based Management, managing and configuring the Modular Switch becomes easier. From

Figure 5-13 The Static Address page Broadcast Storm Filter Excessive broadcast packets (broadcast storms) can be filtered in our managed switch by

Port Mirror If you want to monitor all receive and transmit packets of one port. You can do the following: • Choose the monitored port in "

IP Config You can change the IP address, subnet mask and default gateway of the managed node. (You can also do that from RS232 console). Enter the

Figure 5-16 The IP Config page SNMP To set system name, system location and system contact, you can type the desired text string in the correspondin

Figure 5-17 The SNMP page Save and Reboot Save You can save current settings by click the "Current Settings" checkbox then press th

If you want to use the factory default settings, click the "Factory Default Settings" checkbox then press the "Apply" button next

"Browse" button to select the file.) • Press the "Upgrade" button. Figure 5-19 Upgrade page After you have successfully upgr

SNMP Management The switch MIB options are accessible through SNMP. Instead of defining a large set of commands, SNMP p

GETNEXT Specify an SNMP object in a network device and then retrieve information about the next few SNMP objects in the device. SET Modify and stor

Compliance IEEE 802.3u 100BASE-TX/FX Ethernet, IEEE 802.3z 1000BASE-LX/SX Ethernet, IEEE 802.3ab 1000BASE-T Gigabit Ethernet ANSI/IEEE standard 802.3

Intelligent Module Features  Web-Based Management  SNMP Management  Console and Telnet Management  IEEE 802.1Q Tagging VLAN ( Up to 40

Operational Humidity 10% to 90% ( Non-condensing ) Power Supply Input rate: 100~240VAC, 50~60Hz Internal universal power supply: DC 3.3V/13A, 5V/4A

Appendix A. Internet Explorer Setting If using IE 4.x and later version, you have to modify the browser setting to enable Java applets to use n

Step 3 : click “ sites ” Step 4 : add the IP of the Modular Switch to the zone, click " Add " Step 5: D

Step 6: go back to Internet Options, then click “ Customer Level ” Step 7: pull down rolling to find “Java ” Step 8: selec

Step 9:select”Java Custom Setting” Step 10: select “EditPermissions” Step 11: select “Enable” under ”Unsigned Content”

Appendix B. VLAN Setting In Appendix B, We provide two examples of VLAN management on VLAN Group Configuration. The two examples will show you ho

Before you begin to create new VLAN Group, you need to set PVID number on Ports page as below: We set VLAN ID of Ports (1~4 ) 1, and PVID of Ports

Afterwards, you click to select Port 4 and Port 5 for the purpose of overlapping. Remember to click “ Apply “ button after you finish your setting.

First, on Ports page, we set VLAN ID 1, 2, 3 as below. Click the checkbox of Tagged on Module 1, port 1.( ,which is a Gigabit port ) Remember to cli

Continue to press 》》button and the next page VLAN 3 appears Click the checkbox on Port 1, Module 1. Remember to click “ Apply “ button after you

Web-based Management The Modular Switch provides an embedded HTML web site residing in flash memory. It offers advanced management features and al

Appendix C. Technical Support and Service For this advanced Intelligent Switch, we provide easy access to technical support information through

If pack your hardware, using the original carton if possible, with RMA number written on. After the hardware is repaired, we will inform you, giving y

Package Contents Unpack the carton of the Modular Switch and verify them against the checklist below.  Modular Switc

2. Product Overview This section contains the following topics:  Physical Description  Optional Modules  Installing Optional Modules  Software